Part No. 113201-7MDG30PCC Installation Manual(30 lb Single Pocket, Phase 7 Coin)RETAIN THESEINSTRUCTIONS IN ASAFE PLACE FORFUTURE REFERENCEAVERTISSEME
6 Maytag Co. 113201- 7SECTION IIIINSTALLATION PROCEDURESInstallation should be performed by competent technicians in accordance with local and state c
113201- 7 Maytag Co. 7B. LOCATION REQUIREMENTSBefore installing the dryer, be sure the location conforms to local codes and ordinances. In the absen
8 Maytag Co. 113201- 7C. DRYER ENCLOSURE REQUIREMENTSBulkheads and partitions should be made of noncombustible material.NOTE: Allowances must be made
113201- 7 Maytag Co. 9D. FRESH AIR SUPPLY REQUIREMENTSThe air supply (make-up air) must be given careful consideration to ensure proper performance o
10 Maytag Co. 113201- 7E. EXHAUST REQUIREMENTSExhaust ductwork should be designed and installed by a qualified professional. Improperly sized ductwo
113201- 7 Maytag Co. 11SINGLE DRYER VENTINGHORIZONTAL VENTINGWhen horizontal single 8-inch (20.32 cm) venting is used, the ductwork to the outlet cann
12 Maytag Co. 113201- 7MULTIPLE DRYER (COMMON) VENTINGHORIZONTAL VENTINGIf it is not feasible to provide separate exhaust ducts for each dryer, ducts
113201- 7 Maytag Co. 13VERTICAL VENTINGIllus. DMULTIPLE DRYER VENTING (VERTICAL)The maximum length of venting from the last dryer to where it exhausts
14 Maytag Co. 113201- 7GASELECTRICAL SERVICE SPECIFICATIONS (PER DRYER)NOTES: A. B.When fuses are used they must be dual element, time delay, curren
113201- 7 Maytag Co. 15For 110V ApplicationsSingle-Phase (1ø) Electrical Connections LeadsBlack+PositiveWhite-NeutralGreenGroundorL23. GroundingA grou
FOR YOUR SAFETYDo not store or use gasolineor other flammable vaporsand liquids in the vicinity ofthis or any other appliance.POUR VOTRE SÉCURITÉNe pa
16 Maytag Co. 113201- 7G. GAS INFORMATIONIt is your responsibility to have ALL plumbing connections made by a qualified professional to ensure that t
113201- 7 Maytag Co. 17TYPE OF GASNATURAL LIQUID PROPANE Manifold Pressure* 3.5 inches W.C.8.7 mb10.5 inches W.C.26.1 mb In-Line Pressure 6.0 - 12.0
18 Maytag Co. 113201- 73. Piping ConnectionsALL components/materials must conform to National Fuel Gas Code Specifications ANSI Z223.1-LATESTEDITION,
113201- 7 Maytag Co. 19Consistent gas pressure is essential at ALL gas connections. It is recommended that a 3/4-inch (19.05mm) pipe gas loop be inst
20 Maytag Co. 113201- 7IMPORTANT: If during installation the lint door safety chain was disconnected, it must bereconnected or personal injury may res
113201- 7 Maytag Co. 21NOTE: The sail switch can be checked for proper operation by opening the lint door while heatingcircuit (gas burner or electric
22 Maytag Co. 113201- 72. Mechanical Drop/Rotary Coin Meter or Slide Coin Metera. Insert coin and turn knob (rotary type meter), or for slide meter un
113201- 7 Maytag Co. 23SECTION IVSERVICE/PARTS INFORMATIONA. SERVICEService must be performed by a qualified trained technician, service agency, or g
24 Maytag Co. 113201- 7SECTION VWARRANTY INFORMATIONA. RETURNING WARRANTY CARDSBefore any dryer leaves the manufacturer’s test area, a warranty card
113201- 7 Maytag Co. 25SECTION VIROUTINE MAINTENANCEA. CLEANINGA program and/or schedule should be established for periodic inspection, cleaning, and
IMPORTANTYOU MUST DISCONNECT AND LOCK OUT THE ELECTRIC SUPPLY AND THE GASSUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR GUARDS AREREMOVED FROM THE MA
26 Maytag Co. 113201- 7WARNING: THE ACCUMULATION OF LINT IN THE EXHAUST DUCTWORK CANCREATE A POTENTIAL FIRE HAZARD.WARNING: DO NOT OBSTRUCT THE FLOW O
113201- 7 Maytag Co. 27SECTION VIIDATA LABEL INFORMATIONWhen contacting the Maytag dealer, certain information is required to ensure proper service/pa
28 Maytag Co. 113201- 7SECTION VIIIPROCEDURE FOR FUNCTIONAL CHECKOF REPLACEMENT COMPONENTS1. Microprocessor Controller (Computer) Boarda. Upon complet
113201- 7 Maytag Co. 292. For Models with Direct Spark Ignition (DSI) Module (Type I)Theory of Operation:Start the drying cycle. When the gas burner
30 Maytag Co. 113201- 7SECTION IXMANUAL RESET BURNER HI-LIMIT INSTRUCTIONSA. PHASE 7This dryer was manufactured with a manual reset burner hi-limit t
113201- 7 Maytag Co. 31 Notes _______________________________________________________________________________________________________________________
Part No. 113201 7 - 09/16/08 - 10
WARNINGThe dryer must never be operated with any of the back guards, outer tops, or servicepanels removed. PERSONAL INJURY OR FIRE COULD RESULT.IMPOR
SECTION ISAFETY PRECAUTIONS ... 2SECTION IISPECIFICATIONS
2 Maytag Co. 113201- 7SECTION ISAFETY PRECAUTIONSWARNING: For your safety, the information in this manual must be followed to minimize the risk offire
113201- 7 Maytag Co. 3WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, orsimilarly textured rubber materials.
4 Maytag Co. 113201- 7SECTION IISPECIFICATIONSShaded areas are stated in metric equivalents 3/10/04NOTE: The manufacturer reserves the right to make c
113201- 7 Maytag Co. 5SpecificationsNOTE: The manufacturer reserves the right to make changes in specifications at any time withoutnotice or obligatio
Comments to this Manuals